Aerodynamics in Cycling: What It Is and Why It Matters (Part 1 of 3)

Also in: DeutschFrançaisItalianoEspañolPortuguês

Cycling aerodynamics can seem confusing, even mysterious. It shouldn’t. Whether you are a seasoned racer or a beginner, understanding aerodynamics helps you ride faster, ride smarter and choose the right equipment. On flat roads, 70 to 90 percent of your effort goes into overcoming air resistance.

This first part of our three-part series explains aerodynamics in cycling as a physical phenomenon. You will learn how much power it takes to double your speed (eight times the power!), what aerodynamic drag is (yes, it really is a drag) and why some shapes are more aerodynamic than others. Once you understand these basics, you can work out a great deal on your own.

Part 2 shows how hard it is to measure the aerodynamics of bikes and components, in the wind tunnel and on the road. Part 3 turns to practical choices: gear and drafting. Together, the three articles will guide your riding and equipment decisions and make you a faster cyclist. We will often refer back to this series when we review specific cycling gear.

Why aerodynamics matters in cycling

Cycling is a fairly simple affair. The power you put into the pedals becomes forward motion. What separates fast from even faster is, on the one hand, how much power you can produce and, on the other, how well you overcome the forces of nature that work against you.

Diagram of the forces acting on a cyclist: pedaling power, gravity, rolling resistance and aerodynamic drag
The forces at play while cycling. Illustration by TrainingPeaks.

The illustration above shows these forces. Power moves the rider forward; gravity pulls rider and bike toward the ground. Yes, gravity is a force to overcome, too: think of sliding an empty versus a full water bottle across a table. Then there is rolling resistance and, finally, aerodynamic drag. Together, these forces work against your power. To get the highest possible speed from the power you have, you must reduce these counterforces. You do that by understanding them and adapting your position and equipment.

As you will see below, aerodynamic drag is the most important of these forces, accounting for 70 to 90 percent of the total resistance on flat roads. It is also the most complex. So let’s start with the physics.

The physics: the aerodynamic drag formula

As they move forward, rider and bike must push the air in front of them out of the way. This air resistance, or more precisely aerodynamic drag, follows this formula:

FD=CdA×12ρ×v2 F_D = CdA \times \frac{1}{2}\rho \times v^2
  • CdA (drag coefficient × frontal area): in simple terms, how aerodynamic the whole system of rider and bike is. “Cd” describes how aerodynamic the shape is, and “A” is the frontal area that “sees” the wind. This makes intuitive sense: a smaller object pushes less air out of the way, and a more streamlined shape slips through it more easily. Both mean less drag. Typical values for cyclists range from about 0.5 m² for an upright rider down to 0.2 m² for a very aero time trial position.
  • ρ (the Greek letter rho): the density of the air. The less dense the air, the lower the drag. Air density depends on atmospheric pressure, temperature and humidity, so it changes with location and weather. It decreases at higher altitude, which is why hour record attempts were made at the velodrome in Mexico City, at about 2,230 m above sea level. Warmer air is less dense, and, perhaps surprisingly, so is more humid air.
  • v (velocity): the speed at which rider and bike travel. It is squared! Drag rises with the square of your speed, and the power needed to overcome it rises with the cube. That is one of the main reasons why aero matters so much.

To double your speed, you need 8x the power

Because drag grows so steeply with speed, aerodynamics plays a crucial role. Put simply, to double your speed on the bike, you need eight times the power to overcome the additional aerodynamic drag.

Yes, eight times! Why? At double the speed, you hit twice as many air particles, and you hit them twice as hard. That is already four times the aerodynamic drag, as the formula above shows. The power needed to overcome this drag is drag multiplied by speed, and the speed has doubled, too: 4 × 2 = 8.

Confusing? Here is a simplified formula:

new speed3current speed3×current power=new power \frac{new\space speed^3}{current\space speed^3} \times current\space power = new\space power

Say you need 50 W to ride at 20 km/h. To double your speed to 40 km/h, you need 400 W. Likewise, going from 30 km/h at 200 W to 40 km/h takes about 474 W. This simplified formula ignores rolling resistance and assumes no wind, but it shows the trend. If you ride with a power meter, you have probably felt it: at high speeds, every extra km/h costs far more watts than at low speeds.

Aerodynamic drag is more than air resistance

The simple mental model of aerodynamics in cycling is the power needed to push away the air ahead of us. It is a good model, but reality is a little more complicated, and the model fails to explain some effects we observe. To understand why some shapes are more “aero” than others, we need to look at aerodynamic drag in more detail, specifically at what influences the drag coefficient, the “Cd” in the formula above. It has two components: pressure drag and friction drag.

A blunt round shape with turbulent separated airflow behind it next to a streamlined teardrop shape with smooth airflow
Airflow around a round shape versus an aerodynamically optimized shape. Both have the same frontal area exposed to the wind. The streamlined body is more aerodynamic because it reduces airflow separation behind it. This lowers the pressure difference between front and back and therefore the pressure drag, which otherwise pulls the object backward. Adapted from Easton’s whitepaper on aerodynamics.

As we ride, the air in front of us is compressed and under higher pressure, while the air behind us is at lower pressure. This pressure difference creates a force that slows us down, called “pressure drag”. When an object is blunt, the airflow separates from it and leaves a low-pressure zone behind it. The result is more pressure drag: the object is literally “pulled from behind.” When an object is streamlined, or “aero,” the air flows around it without separating. The low-pressure zone is smaller, and so is the pressure drag.

Then there is “friction drag”, the energy lost to friction as air flows over the surface of an object. The more the air clings to the surface, the more power you need to move forward. The right materials and surface textures reduce friction drag and make an object more aero.

Round is not aero, be it steel tubes, shifting cables or legs

From what we have learned so far, designing the optimal shape for aero bikes and components is a significant engineering challenge. It is an optimization problem, because aerodynamics is not the only criterion. First and foremost, a component must do its job reliably, whether it is a head tube, a seat post or a helmet.

Drag coefficients of common shapes: sphere, half-sphere, cone, cube, cylinder, bullet and airfoil
Drag coefficients of common shapes, provided by NASA. Round shapes such as cables, tubes and legs perform poorly and can have up to 10 times the drag coefficient of a fully optimized airfoil.

NASA and others have researched ideal aerodynamic shapes extensively; some examples are shown above. For the same frontal area, an airfoil has a drag coefficient (Cd) of 0.045, compared with about 0.3 for a bullet and about 0.5 for a sphere. It is hard to grasp intuitively that a much bigger object can have similar aerodynamic drag simply because its shape is more aero. Still, the data show a difference in Cd of up to ten times between the round tubes of an old steel bike and the shapes of a modern aero frame. That is a lot! At the extreme, a tiny 5 mm round shifting cable hanging from your bike might cause as much aerodynamic drag as a 5 cm wide, aero-optimized head tube.

These differences matter most at the front of the bike, where rider and bike hit clean air. That is why front wheels, handlebars, internal cable routing and helmets are key areas for aerodynamic optimization, as we will see in future articles.

The three ways to be aero: smaller, more streamlined, more slippery

In summary, to minimize the CdA part of aerodynamic drag, you want:

  • Smaller: the smallest possible frontal area in the wind, the “A” in the equation.
  • More streamlined: a shape that keeps the airflow attached, the main part of “Cd”.
  • More slippery: a surface the air flows over easily, the rest of “Cd”.

Bike engineers optimize all of these in frames, wheels, helmets, clothing and other components. The question remains: who does it best? Which equipment is really the most aero for the way I ride?

Well… it depends. As we will see in Part 2 of this series on aerodynamics in cycling, identifying the most aerodynamic setup remains highly complex, despite computational fluid dynamics (CFD), wind tunnels and the latest real-world testing technology.

Filippo Ganna in an aero time trial position on the track during his hour record ride
Filippo Ganna at the Grenchen velodrome in Switzerland, on his way to a new hour record of 56.792 km on October 8, 2022. His record owed much to his incredible power and to one of the most aerodynamically optimized setups ever ridden. Photo: AP.